DemoPad.com

Today through the demopad, control in my living room TV, PROJECTOR, RECEIVER, SKY, BR, APPLE TV with the help of the Global Cache IR - very good.

In search here on the site, it is possible that will control my Receiver (MARANTZ SR7007) with Direct Ethernet IP Control

I'm more lost than blind shootout

Anyone would have a video tutorial or help?

I need something from the beginning,
Example: Commando MARANTZ for POWER
MUON<CR>
MUOFF<CR>

<CR> --- what's this?

Inside the Program demopad where I put the IP commands?

thank you

The Marantz uses the same protocol as the Denon Receivers.
But there is a Marantz file available on the forum
http://www.demopad.com/forum/viewtopic.php?f=26&t=2647

To add a device look at this.
http://www.demopad.com/forum/viewtopic.php?f=7&t=51

CR is carriage return, you don't need the CR in the command, just the text.

Wherever you see <CR> in the document, this is carriage return, hex 0D, so \x0D in our software (this would be a sensible default command suffix).

I want to thank you both.

I'll try again and post results.

My doubts,
Marantz codes of the link, this even after playing them in Demopad, seem to me to be of IR codes, am I wrong? or these codes serve to control via IP?

Your IP codes here

http://www.awe-europe.com/documents/Con ... OL_V02.xls

My sincere thanks @ starwarsmike

I think I'm creating a monster with 7 heads. (jajaja: D)

Basico - I just want to connect via IP MARANTZ SR7007

What I have done:

1 - New Device
2 - IP Address / Port
3 - then click on VIEW / EDIT.
4 - Open a window - Command Data field
5 - code - PWON
6 - add
7 - Assign code to a button.

I'm on the right track? or am I wrong?
The command to turn it would just PWON? - Simple?

I'll post the Denon codes that will also control the Marantz and full instructions for you today.

OK Here is the methods.
There are two methods for controlling the Denon/Marantz receivers.

The first method uses a JSON Api that is comprehensive in what you can control, however it has a limitation that only one device at a time can control it. If you only have one ios device I suggest you use this method. (that is the one you have been trying).

To use this method use the device file here:
http://www.demopad.com/forum/viewtopic.php?f=26&t=67
And set your Marantz Device with your receiver IP address, Generic IP device, Port 23, check maintain active connection. Note you also have to enable remote control on your receiver (see your manual)

The second method is the one that Denon uses in there own ios remote and sends the commands via http. This allows only a subset of commands, though still powerful. It does not have a limit on the number of devices that can control it. Note this method has not been published by Denon and no Api is available all commands were reverse engineered.
Use at your own risk.

To use this method use the attached Denon HTTP Device file and set your Marantz Device with your receiver IP address, Generic IP device, Port 80, and DO NOT check maintain active connection.

@michaelbnt
So did you get the IP control of your Marantz working.

I'm like a child in learning (jajaja)

I'm using the first method JAS API. I saw that the door was my mistake because @ trevorst recommended port 23, and the menu of the receiver was on the wrong door.

Using iTest application can seamlessly run all command.
However, to play it in DEMOPAD and then the iPad can run only one command after he did not respond.

In Example Demopad

I made a button, put the function + Vol.

When tightening since it works when not return to squeeze back works. The only method is to return demopad close and re-open it

Any idea?

Hi Michael,
Not sure what you are saying as your using terms that I don't know.

When you say door are you referring to the Port.??

"Using iTest application can seamlessly run all command."
What is the program iTest you refer to??

When tightening since it works when not return to squeeze back works. The only method is to return demopad close and re-open it
This statement makes no sense, what are you tightening and what are you squeezing.

Make sure you are using the generic IP device type, leave the terminator as is and have the maintain active connection checked and disconnect after unchecked

@ trevorst - You have been a great teacher.

Yes I meant the door is yes PORT. (excuse the lack of detail)

The ITEST program is a program coming from Global Cache website. (I was wrong thinking that was original iTest

I'll explain.

Demopad project.
IP address: 192.168.1.xxx
Port 23
Type: Generic Device IP

View / Edit:
DENON AVR4311CI_AVR4311.dc1

Demopad APP in IPAD.

Click on a button - (actions) Receiver Marantz respoder OK
Click the same button - nothing happens.

unable to express myself?
complicated situation?

try to show for photos in next post

I think you are mixing IR (global Cache) with IP.
What Global Cache unit do you have??

The IR system was disabled.
Global Cache IR unit - worked perfectly.
However I want to learn the commands over IP.

Working once IP command, it should work again and again.
Unfortunately this does not occur.

I'll study this weekend and will post results
madness

discover my mistake.
I had to change the "COMMAND SUFFIX" to \ x0D is the receiver worked perfectly

Now I have difficulty with 2 way feedback.
I'm not managing to get answer
I want something simple
Indentify if the receiver is powered on or off