Search found 226 matches

by cv27
Mon Apr 23, 2018 6:10 pm
Forum: Help Forum
Topic: Need help: Feedback from GET-request
Replies: 2
Views: 84

Re: Need help: Feedback from GET-request

I suspect your 2-way feedback specifies the default \0D response terminator. The last line you're interested in ends with a ';' and no CrLf as with the other lines, so DemoPad won't tackle that last line until a \0D si detected. If you only need to react to lines that end with ';' then change the re...
by cv27
Tue Apr 03, 2018 6:43 pm
Forum: Help Forum
Topic: Reorder feedbacks
Replies: 5
Views: 216

Re: Reorder feedbacks

+1 While we're at it, how about the ability to: Order subpages by dragging them up/down Order Number custom actions by minimal value Order flags, labels and numbers by dragging them up/down Why? Because, as we fine tune or expand our projects, the number of entries can grow dramatically and it beco...
by cv27
Tue Apr 03, 2018 6:42 pm
Forum: Help Forum
Topic: Reorder feedbacks
Replies: 5
Views: 216

Re: Reorder feedbacks

It doesn't save the associated actions, because they are project specific. it would be nice if it did save the actions, as an option, with all the appropriate disclaimers. It would have saved me hours of work re-entering actions, already defined in a previous version of a project (same variables, d...
by cv27
Sat Mar 31, 2018 6:31 pm
Forum: General Discussion
Topic: Sharing new design - lets get the forum moving again :)
Replies: 6
Views: 313

Re: Sharing new design - lets get the forum moving again :)

rhett7660 wrote:
Fri Mar 30, 2018 10:20 pm
I would imagine it would be some of the iRule button sets with a combination of Photoshop files.
I suspect as well, but there is no way to explain the transparency of some of the buttons, unless those were 'hand crafted' to simulate transparency.
by cv27
Sat Mar 31, 2018 6:29 pm
Forum: Help Forum
Topic: Strange happening
Replies: 1
Views: 144

Re: Strange happening

When I ran DemoPad solo (I now use a Centro-M), I used to get into these situations here and there and, as you, would kill and restart the app so things would go again. There is also 'disconnect from/connect to device' commands available you could try that close/reopen the TCP conversation, but thos...
by cv27
Fri Mar 30, 2018 6:33 pm
Forum: General Discussion
Topic: Sharing new design - lets get the forum moving again :)
Replies: 6
Views: 313

Re: Sharing new design - lets get the forum moving again :)

Good looking design!

Some of your buttons are not part of Free or Pro Set Graphics 1-5. Some buttons even appear to have transparency.

Did you design these buttons yourself? If so, what tool did you use?

Care to share some of your technics?
by cv27
Thu Mar 29, 2018 7:15 am
Forum: Help Forum
Topic: Reorder feedbacks
Replies: 5
Views: 216

Re: Reorder feedbacks

+1 While we're at it, how about the ability to: Order subpages by dragging them up/down Order Number custom actions by minimal value Order flags, labels and numbers by dragging them up/down Why? Because, as we fine tune or expand our projects, the number of entries can grow dramatically and it becom...
by cv27
Wed Mar 28, 2018 10:39 pm
Forum: Help Forum
Topic: iPad page scrolling
Replies: 27
Views: 878

Re: iPad page scrolling

FYI, Well after spending about 2 hours and finally going back to the iRule forum, I was able to get WOL to work work for my HTPC. In the DemoPad example it shows an IP address that needs to be something like 192.168.1.255. In my case 255.255.255.255 as explained in the iRule forum, finally did the ...
by cv27
Mon Mar 26, 2018 4:32 pm
Forum: Help Forum
Topic: Sony Projector IP command issue
Replies: 6
Views: 279

Re: Sony Projector IP command issue

anderdea wrote:
Sun Mar 25, 2018 9:49 pm
I’m not familiar with Hercules?
Info on Hercules https://www.hw-group.com/products/hercu ... ex_en.html. But there are other utilities (Packet Sender, IPtools ...).
by cv27
Sun Mar 25, 2018 5:36 pm
Forum: Help Forum
Topic: iPad page scrolling
Replies: 27
Views: 878

Re: iPad page scrolling

Pretty busy display: I just hope you're not using a cell. phone to navigate ;) I actually started this way, trying to get all the possible options onto one page. I use a mini iPad and even then found that I had to be very careful how I pressed the buttons. My design has evolved over the years to onl...
by cv27
Sun Mar 25, 2018 5:12 pm
Forum: Help Forum
Topic: Sony Projector IP command issue
Replies: 6
Views: 279

Re: Sony Projector IP command issue

Try using some network tool such as Hercules to first test out your commands. Much faster to setup and test and your get the integral response from the device. The response will often give clues as to what's wrong. Also make sure you have the right command suffix. In cases where the device does not ...
by cv27
Mon Mar 12, 2018 10:52 pm
Forum: Device Command Database
Topic: Samsung TV 2016+ RS232 commands
Replies: 0
Views: 275

Samsung TV 2016+ RS232 commands

Attached are the RS232 commands available for Samsung TV's 2016+. They have been tested on a MU8000 which has the EX-Link RS232 connector on the back panel. Notes: Do NOT append a command suffix If using a Global Caché Flex with RS232, port is TCP 4999 2-way (or not) - the MU8000 acknowledges valid ...
by cv27
Tue Mar 06, 2018 5:57 am
Forum: Device Command Database
Topic: Samsung TV Commands
Replies: 19
Views: 16248

Re: Samsung TV Commands

trevorst wrote:
Mon Feb 16, 2015 8:44 pm
... I didn't have any success, gave up and I am now using RS232.
I'm going the RS232 route as well. Could you share your Samsung model & year and the RS232 commands?
by cv27
Thu Feb 22, 2018 11:56 pm
Forum: Device Command Database
Topic: Samsung TV Commands
Replies: 19
Views: 16248

Re: Samsung TV Commands

The UN82MU8000 has a different pedestal:
UN82MU8000.png
I'll probably use some clip to snap the emitter to the bottom edge, if I stick to IR. RS232 has its quirks.
by cv27
Wed Feb 21, 2018 7:44 pm
Forum: Device Command Database
Topic: Samsung TV Commands
Replies: 19
Views: 16248

Re: Samsung TV Commands

I agree, what I ended up doing was running the emitter along the silver base and then aiming it up to the IR port. You can't see the emitter and it works like a charm. I had it stuck originally, but it kept falling off. I have never used the RS232, thought about it, I just haven't done it. Mainly b...